Net Gamer

ASTM A682 PDF

ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.

Author: Fenrira Bajora
Country: Malaysia
Language: English (Spanish)
Genre: Relationship
Published (Last): 2 May 2018
Pages: 313
PDF File Size: 15.69 Mb
ePub File Size: 8.1 Mb
ISBN: 630-4-56404-853-6
Downloads: 45064
Price: Free* [*Free Regsitration Required]
Uploader: Jutaur

However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. Conformance to SI tolerances is mandatory when w682 “M” specification is used. Rework and Retreatment Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Unless otherwise agreed to, all tests and inspections, except product analysis, shall be made at the place of production.

Limits on such elements are by agreement between purchaser and supplier. However, under SI the preferred term in mass. The values stated in aatm system are not exact equivalents; therefore, each system must be used independently of the other.

Materials and Manufacture 5. Thickness Tolerances Plus or Minus, in. However, unless the order speci? It is normally produced as a fully killed steel. Each of the elements listed in Tables 2 and 3 and additional elements agreed upon by the purchaser and the supplier shall be included in the report of heat analysis. Link to Active This link will always route to the current Active version of the standard.

The material must be adequately protected and correctly identi?

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  LA SIRENA VARADA CASONA PDF

ASTM A, AM_百度文库

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. General Requirements for Delivery 4. Within the text, the SI units are shown in brackets. For strip length under mm, camber tolerance shall be subject to negotiation.

NOTE 3—When the camber tolerances shown in Table 8 are not suitable for a particular purpose, cold-rolled strip is sometimes machine straightened. Government procurement by the Defense Supply Agency, strip material shall be continuously marked for identi?

If you feel ashm your comments xstm not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. NOTE 2—The industry de? However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. Rejection and Rehearing NOTE 1—Camber is the greatest deviation of a side edge from a straight line, the measurement being taken on the concave side with a straight edge.

When the maximum manganese limit exceeds 1. When the amount of copper, nickel, chromium, or molybdenum is less than 0. Finish and Edges The strip may be subjected to product analysis by the purchaser either for the purpose of verifying that the chemical composition is within speci?

The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. When required, minimum coil weights are subject to negotiation. However, under SI the preferred term in mass. Link to Active This link will always route to the current Active version of the standard.

  04EB58 C848 41B PDF

NOTE 1—The term weight is used when inch-pound units are the standard. NOTE 2—Camber tolerances as shown in the table are for any mm length. Originally published as A — Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the context of the report.

Combining values from the two systems will result in nonconformance with the specification. C When the chromium is speci?

C Number 3 edge strip with thickness tolerance guaranteed at less than 3? Strip is classified as product that is 0. The elements comprising the desired chemical composition are speci? This edge is produced when the width tolerance and edge condition are not as exacting as for No. Table 3 shows requirements for additional elements. Note 1—The term weight is used when inch-pound units are the standard.

Combining values from the two systems will result in nonconformance with the specification. In case of dissatisfaction with the results of the test, the manufacturer may make claims for a rehearing.

ASTM A682 Grade 1074

Revision to Table 2. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. B Measured 10 mm or more in from edge; and on narrower than 25 mm, at any place between edges.